manualshive.com logo in svg

Rethink Robotics Sawyer, Original Instructions Manual, Page: 166 / 220

Share
Download
Rethink Robotics Sawyer Original Instructions Manual Download Page 166

159

Intera 5.3

Task 2: Pick and Place task with joint acceleration set to Express

A typical Pick and Place task where the robot is picking an object from a table, moving approxi-
mately 120 degrees around J0, placing the object, and stating again.  The joint acceleration setting 
in the software is set to 

express

 and the move is defined as a 

joint

 move. The payload is zero. In this 

scenario, the maximum measured tip speed is 1.46 m/s as seen in the graph below.

Figure D- 2: Chart showing the endpoint velocity for a specific task. This task is a standard pick and 
place where the robot is rotating about 120 degrees around its base.  The joint acceleration setting 
is set to 

express

 in the Intera software.

Task 3: Improbable task with joint acceleration set to Express

An improbable task where the robot is extended vertically, and is trained to move 180 degrees 
between two poses.  The arm is trained to maximize velocity at the tool tip by moving in J0 and J2. 
The joint acceleration setting in the software is set to 

express 

and the move is defined as a 

joint

 

move. The payload is zero. In this scenario, the maximum measured tip speed is 2.82 m/s as seen 
in the graph below.

Important Note – This graph is meant to show the theoretical maximum for tool tip speed.  Under 
normal operating conditions for standard tasks the robot is designed for, the max tip speeds will 

Summary of Contents for Sawyer





























































































































































































































Reviews:

No comments