OUT_DURING_SEARCHING_FOR_PES pes.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_FOUND_PES
48Dh
Servo
Timeout during head stepper offset calibration found pes.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_FOUND_PES
48Eh
Servo
Timeout during head stepper offset calibration stopping after
found pes.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_MOVING_UP_WITH_ADDED_HYSTERE
SIS
48Fh
Servo
Timeout during head stepper offset calibration moving up with
added hysteresis.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_ADDED_HYSTERE
SIS
490h
Servo
Timeout during head stepper offset calibration stopping after
added hysteresis.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_CAPTURING_PES_SAMPLES
491h
Servo
Timeout during head stepper offset calibration capturing pes
samples.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_GOING_TO_NEW_
OFFSET
492h
Servo
Timeout during head stepper offset calibration stopping after
going to new offse
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_MOVING_UP_WITH_ADDED_HYSTERE
SIS_FOR_VERIFICATION
493h
Servo
Timeout during head stepper offset calibration moving up with
added hysteresis f
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_VERIFYING_NEW_OFFSET
494h
Servo
Timeout during head stepper offset calibration verifying new
offset.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_GOING_TO_OFFSE
T
495h
Servo
Timeout during head stepper offset calibration stopping after
going to offset.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_REFERENCE_SEN
SOR_LOW
496h
Servo
Timeout during head stepper offset calibration stopping after
reference sensor l
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_REFERENCE_SEN
SOR_HIGH
497h
Servo
Timeout during head stepper offset calibration stopping after
reference sensor h
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_STOPPING_AFTER_PES_FOUND
498h
Servo
Timeout during head stepper offset calibration stopping after
pes found.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_DEALING_WITH_HYSTERESIS
499h
Servo
Timeout during head stepper offset calibration dealing with
hysteresis.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_MOVE_UNTIL_REFERENCE_SENSOR_
LOW
49Ah
Servo
Timeout during head stepper offset calibration move until
reference sensor low.
SRV_HEAD_STEPPER_OFFSET_CALIBRATION_TIME
OUT_DURING_MOVE_UNTIL_REFERENCE_SENSOR_
HIGH
49Bh
Servo
Timeout during head stepper offset calibration move until
reference sensor high.
SRV_LPOS_NEW_ESTIMATE_JUMPED_MORE_THAN_
2_FROM_PREVIOUS_RELATIVE_LPOS
49Ch
Servo
New estimated LPOS should never jump more than 2 from
previous relative_lpos.
SRV_CMDPROC_CMD_REJECT_DRIVE_MECH_STUC
K
49Dh
Servo
Drive requires recovery command to 'unstuck' mechanics
SRV_CMDPROC_EMERGENCY_EJECT_IN_PROGRES
S_ABORT_NOT_VALID
49Eh
Servo
Abort rejected because emergency eject was in progress
SRV_SEQ_INVALID_HIGHER_PRIORITY_COMMAND_
RECEIVED
49Fh
Servo
A higher priority command was received from the command
processor that was not a
SRV_INVALID_REEL_STATE_FOR_SET_RUN_TENSIO
N_COMMAND
4A0h
Servo
Invalid reel state for set run tension command.
SRV_SEQ_NON_STANDARD_CARTRIDGE_RADIUS 4A1h
Servo
Calculated radius does not match possible radii for cartridges
SRV_TIMEOUT_DURING_HEAD_STEPPER_IDLE 4A2h
Servo
Timeout during head stepper idle.
SRV_TIMEOUT_DURING_HEAD_STEPPER_STARTING 4A3h
Servo
Timeout during head stepper starting.
SRV_TIMEOUT_DURING_HEAD_STEPPER_MOVING_T
O_POSITION
4A4h
Servo
Timeout during head stepper moving to position.
SRV_TIMEOUT_DURING_HEAD_STEPPER_STOPPING
_AFTER_MOVING_TO_POSITION
4A5h
Servo
Timeout during head stepper stopping after moving to position.
SRV_TIMEOUT_DURING_HEAD_STEPPER_MOVING_
UP_WITH_ADDED_HYSTERESIS
4A6h
Servo
Timeout during head stepper moving up with added hysteresis.
SRV_TIMEOUT_DURING_HEAD_STEPPER_VALIDATI
NG_PES
4A7h
Servo
Timeout during head stepper validating pes.
Summary of Contents for LTO 4
Page 1: ......