hub.
SRV_UNTHREAD_PULL_NO_STALL
09C7h
Servo
Pulling tape to the cart reel didn't stall
SRV_UNTHREAD_PULL_UNEXPECTED_STALL
09C8h
Servo
Pulling tape to cart reel stalled before the pin could reach the
grabber mover.
SRV_REEL_HW_DID_NOT_DETECT_STOP 09C9h
Servo
This
is
an exception when HW does not detect stop condition
SRV_PIN_GRABBER_PRE_INIT_STUCK_ZONE_A 09CAh
Servo
Cannot move the pin grabber out of zone A to zone C2 during
pre-initialization.
SAS_INTERFACE_CTIO_ABORTED 09CBh
SCSI
Thread aborted by initiator
SAS_INTERFACE_CTIO_CRCERROR 09CCh
SCSI
SDRAM CRC error
SAS_INTERFACE_CTIO_CRCERRORAUTOGOOD 09CDh
SCSI
SDRAM CRC error after autogood sent
SAS_INTERFACE_CTIO_CTIOM0SCBERR 09CEh
SCSI
SAS_SSP_TGT_CtioM0Start out of rsrcs
SAS_INTERFACE_CTIO_CONNECTIONDOWN 09CFh
SCSI
Connection went down mid-transfer
SAS_INTERFACE_CTIO_DMAPARITYERROR 09D0h
SCSI
DMA Parity error on Read
SAS_INTERFACE_CTIO_DATAPHASECRCERR
09D1h
SCSI
Data phase CRC error
SAS_INTERFACE_CTIO_I_T_NEXUSLOSS 09D2h
SCSI
I_T Nexus Loss Timer expired
SAS_INTERFACE_CTIO_UNUSED
09D3h
SCSI
Status not needed anymore
SAS_INTERFACE_CTIO_OKRESID
09D4h
SCSI
SSP_DL mismatch with autogood reqst
SAS_INTERFACE_CTIO_OKSTOP 09D5h
SCSI
XferStop completed without errors
SAS_INTERFACE_CTIO_OKSTOPAUTOGOOD 09D6h
SCSI
XferStop did full tautogood
SAS_INTERFACE_CTIO_OPENTIMEOUT 09D7h
SCSI
Open Timeout during open attempt
SAS_INTERFACE_CTIO_PATHWAYBLOCKED 09D8h
SCSI
Pathway Blocked retries exhausted
SAS_INTERFACE_CTIO_PEER_LOGOUT 09D9h
SCSI
Peer logged out while executing CTIO
SAS_INTERFACE_CTIO_XFERMISPECIFIED 09DAh
SCSI XferData
incorrectly
specified
SAS_INTERFACE_CTIO_XFERABORTEDCMD 09DBh
SCSI
XferData attempted of aborted signal
SAS_INTERFACE_CTIO_WWNTABLEERR 09DCh
SCSI
Invalid WWN Table entry during Tx
SAS_INTERFACE_CTIO_WWNIOCOUNTERR 09DDh
SCSI
WN I/O Count reached maximum value
SAS_INTERFACE_CTIO_TASK_UNAVAIL
09DEh
SCSI
Task not available
SAS_INTERFACE_CTIO_SHORTIU 09DFh
SCSI
Short information unit received
SAS_INTERFACE_CTIO_SENDRESPSCBERR
09E0h
SCSI
SAS_SendRespFrame out of resources
SAS_INTERFACE_CTIO_SENDFRAMESCBERR
09E1h
SCSI
SAS_SSP_SendFrame out of resources
SAS_INTERFACE_CTIO_RETRY 09E2h
SCSI
OPEN_REJECT(RETRY) received. Retry.
SAS_INTERFACE_DETECT_WRITE_CRC_ERROR_AFT
ER_COMMAND_DONE
09E3h
SCSI
Controller detect CRC error within SDRAM after send good
response to the host
SRV_PIN_GRABBER_CANNOT_MOVE_OUT_TO_STA
NDBY
09E4h
Servo
Cannot move pin grabber out to the standby position during
initialization.
SRV_CMD_MEM_IS_NOT_COMPATIBLE_WITH_CNTR
L
09E5h
Servo
Controller and Servo both should have same shared memory
address space.
DSM_WORM_SET_CAPACITY_NOT_ALLOWED 09E6h
Data
set
manager
Can't use SET_CAPACITY command on an initialized WORM
cartridge.
SCSI_DETECTED_WORM_CM_CONFLICT_IN_CART_T
YPE
09E7h
SCSI
Some CM fields indicate WORM but cartridge type is not WORM.
SCSI_DETECTED_WORM_CM_CONFLICT_IN_MEDIA_
MFG_WORD
09E8h
SCSI
Some CM fields indicate WORM but Media Manufacturer Info
page - media mfg word n
SCSI_DETECTED_WORM_CM_CONFLICT_IN_FORMA
T_TYPE
09E9h
SCSI
Some CM fields indicate WORM but Initialization Data page
Format Type field does
SRV_DOMAIN_ERROR
09EAh
Servo
Math Function out of domain
SCSI_SET_CAPACITY_NOT_ALLOWED_ON_INIT_WO
RM_CART
09EBh
SCSI
SET CAPACITY is not allowed on initialized WORM cartridges
SCSI_WORM_MODE_NOT_SUPPORTED 09ECh
SCSI
Drive is not configured to support WORM
CM_BAD_ERROR_USAGE 09EDh
Medium
Auxiliary
Memory
CM Error Usage page
CM_BAD_CARTRIDGE_CONTENT 09EEh
Medium
Auxiliary
Memory
CM Cartridge Content page
FC_INTERFACE_CTIO_ABORTED
09EFh
SCSI
Thread aborted by initiator
MIC_CART_TYPE_NOT_RECOGNIZED 09F0h
Medium
Auxiliary
Memory
The Cartridge Manufacturer Information page cart type is not
recognized
FC_INTERFACE_CTIO_CRCERROR 09F1h
SCSI
SDRAM CRC error occurred during transfer.
Summary of Contents for LTO 4
Page 1: ......