Quantum LTO 4, User Manual

Page: 248 / 297

OWN_AT_LPOS_FROM_CRUISE_CONTROL_REVERS
E in reverse direction.
SRV_MOVETAPE_INVALID_DIRECTION_IN_RAMP_DO
WN_AT_LPOS_FROM_CRUISE_CONTROL 24Eh Servo Tape not moving
SRV_MOVETAPE_LPOS_RECEIVED_BEFORE_TRACK
ING_IN_RAMP_UP_STATE 24Fh Servo LPOS notification received before ramp up completed.
SRV_CMDPROC_TAPE_NOT_MOVING_FOR_REPOSIT
ION_CMD 250h Servo Reposition cmd rejected
SRV_MOVETAPE_REPOSITION_FAILED_ALREADY_P
AST_LPOS 251h Servo LPOS already exceeded in reposition_from_idle
SRV_CMD_INVALID_HEADPOSITION_SELECTED_LO
OKUP_TRACKING_RATIO 252h Servo Invalid head position selected in looking up tracking ratio
SRV_MOVETAPE_INVALID_TAPE_DIRECTION_IN_EN
ABLE_HEAD_BIAS_FOR_READ_TRACKING 253h Servo Invalid tape direction was selected in enable head bias function
SRV_MOVETAPE_INVALID_TAPE_DIRECTION_IN_EN
ABLE_HEAD_BIAS_FOR_WRITE_TRACKING 254h Servo Invalid tape direction selected in enable head bias function
SRV_MOVETAPE_INVALID_TRACKING_MODE_IN_EN
ABLE_HEAD_BIAS 255h Servo Invalid tracking mode selected in enable bias function
SRV_GOTO_LC_FORWARD_PHYSICAL_LIMIT_OVER
RUN_DURING_RAMP_UP 256h Servo Physical limit exceded during goto_lc_ramp_up state.
SRV_GOTO_LC_REVERSE_PHYSICAL_LIMIT_UNDER
RUN_DURING_RAMP_UP 257h Servo Physical limit exceded during goto_lc_ramp_up state.
SRV_GOTO_LC_FORWARD_PHYSICAL_LIMIT_OVER
RUN_DURING_WAIT_MARK 258h Servo Physical limit exceded during goto_lc_wait_mark state.
SRV_GOTO_LC_REVERSE_PHYSICAL_LIMIT_UNDER
RUN_DURING_WAIT_MARK 259h Servo Physical limit exceded during goto_lc_wait_mark_state.
SRV_GOTO_LC_FORWARD_PHYSICAL_LIMIT_OVER
RUN_DURING_MARK_FOUND 25Ah Servo Physical limit exceded during goto_lc_mark_found state.
SRV_GOTO_LC_REVERSE_PHYSICAL_LIMIT_UNDER
RUN_DURING_MARK_FOUND 25Bh Servo Physical limit exceded during goto_lc_mark_found state.
SRV_GOTO_LC_FORWARD_PHYSICAL_LIMIT_OVER
RUN_DURING_POSITION_TAPE 25Ch Servo Physical limit exceded during position tape state.
SRV_GOTO_LC_REVERSE_PHYSICAL_LIMIT_UNDER
RUN_DURING_POSITION_TAPE 25Dh Servo Physical limit exceded during position tape state.
SRV_GOTO_LC_INITREELS_API_BUSY_REJECT 25Eh Servo Init reels api call failed with a busy status.
SRV_STEPPER_MOTOR_TASK_INVALID_OPERATION 25Fh Servo 32c
SRV_STEP_LOAD_CART_ERROR1 260h Servo Another event occurred before the cartridge in switch (SNS1)
tripped
SRV_STEP_LOAD_CART_ERROR2 261h Servo The cartridge load motor stalled before it reach it final position
SRV_STEP_LOAD_CART_ERROR3 262h Servo Expecting to see the cartridge in sensor change
SRV_STEP_LOAD_CART_ERROR4 263h Servo Expecting good completion status from cartridge load motor
task
SRV_STEP_LOAD_CART_DEFAULT 264h Servo invalid state in process_load_cart function
SRV_STEP_UNLOAD_CART_ERROR1 265h Servo The firmware failed to hit SNS2 (switch on side of load mech)
SRV_STEP_UNLOAD_CART_ERROR2 266h Servo Error occurred while moving the loading tray past SNS2 (switch
on side of load m
SRV_STEP_UNLOAD_CART_DEFAULT 267h Servo An unexpected state occurred in the cartridge unload task.
SRV_STEP_THREAD_TAPE_ERROR1 268h Servo fRemoving tape slack from the cartridge failed while Threading
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR1 269h Servo expecting SNS1 high
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR2 26Ah Servo expecting steps done
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR3 26Bh Servo expecting serial eeprom done
SRV_STEP_PWR_RECOVERY_LOAD_CART_ERROR4 26Ch Servo expecting SNS1 low
SRV_STEP_THREAD_TAPE_ERROR6 26Dh Servo Load arm motor stalled while going to the cartridge.
SRV_STEP_THREAD_TAPE_ERROR7 26Eh Servo expecting steps done
SRV_STEP_THREAD_TAPE_ERROR8 26Fh Servo expecting MECH_DELAY1_DONE
SRV_STEP_THREAD_TAPE_ERROR9 270h Servo motor stall waiting for SNS13 high
SRV_STEP_THREAD_TAPE_ERROR10 271h Servo SNS13 Did not change to expected value
SRV_STEP_THREAD_TAPE_ERROR11 272h Servo motor stall waiting for ENGAGED_LEADER
SRV_STEP_THREAD_TAPE_ERROR12 273h Servo expecting steps done
SRV_STEP_THREAD_TAPE_ERROR13 274h Servo timer failure