Quantum LTO 4, User Manual

Page: 258 / 297

SRV_MOTOR_POR_STUCK_1 3F4h Servo can't clear reel motor POR flag on startup
SRV_MOTOR_POR_STUCK_2 3F5h Servo can't clear reel motor POR flag after PF clear
SRV_MOTOR_PWR_FAIL 3F6h Servo can't clear reel motor power fail condition on startup
SRV_STATEM_AUTOLOAD_COMMAND_REJECTED_N
O_CART_IN_DRIVE 3F7h Servo Autoload failed
SRV_SZA_LOAD_COMPLETION_FAILURE 3F8h Servo SZA load function did not complete in the allotted time
SRV_TAPE_CUT 3F9h Servo tape cut
SRV_MOVETAPE_ERROR_LP1_UNDERRUN_DURING
_RAMP_UP 3FAh Servo LP1 Underrun during ramp up state
SRV_MOVETAPE_ERROR_LP6_OVERRUN_DURING_
RAMP_UP 3FBh Servo LP6 overrun during ramp up
SRV_MOVETAPE_RAMP_DOWN_API_FAILED_DURIN
G_ERROR_HANDLING 3FCh Servo Ramp down api failed during error handling
SRV_MOVETAPE_LP1_UNDERRUN_IN_CRUISE_CON
TROL 3FDh Servo LP1 underrun during cruise control state.
SRV_MOVETAPE_LP6_OVERRUN_IN_CRUISE_CONT
ROL 3FEh Servo LP6 overrun in cruise control state.
SRV_CMDPROC_NO_CARTRIDGE_IN_DRIVE 3FFh Servo No cartridge in drive
SRV_STEP_HEAD_TRIGGERED_SENSORS_DURING_
HEAD_STEPPING 400h Servo Top or bottom sensors for head stepper were triggered when
they shouldn't have b
SRV_STEP_HEAD_NOT_AT_BASEMENT_POSITION 401h Servo
SRV_STEP_HEAD_COULD_NOT_FIND_PES_DURING_
HEAD_CALIBRATION
402h Servo
SRV_STEP_HEAD_PES_CAPTURE_IS_BAD_DURING_
HEAD_CALIBRATION 403h Servo Max retries exceeded to verify PES during head offset cal.
SRV_STEP_HEAD_INCORRECT_OFFSET_FROM_HEA
D_CALIBRATION 404h Servo
SRV_ROTATE_ENABLEMOTOR_API_REJECT_BUSY 405h Servo Enable Motor API failed at beginning of Rotate command
SRV_EXCEED_LC_LIMIT 406h Servo exceed LC limit
SRV_RAD_COMP_ERR 407h Servo radius computation off
SRV_TAPE_SLACK 408h Servo tape slack
SRV_HIT_EOT 409h Servo hit EOT
SRV_HIT_PEOT 40Ah Servo hit PEOT
SRV_WATCH_DOG 40Bh Servo Watch Dog Timer Interrupt
SRV_EXCEPT_UNDEF_INSTR 40Ch Servo Undefined exception
SRV_EXCEPT_PREFECT 40Dh Servo Prefect exception
SRV_EXCEPT_MEMORY_ABORT 40Eh Servo Memory abort exception
SRV_EXCEPT_SOFTWARE_INTERRUPT 40Fh Servo Software interrupt exception
SRV_EXCEPT_EXCEPTION_CODE_OUT_OF_RANGE 410h Servo Software exception identifier out of range
SRV_GLOBAL_ERROR_STATE 411h Servo Firmware global error state
SRV_REEL_PHYSICAL_EOT_LIMIT_OVERRUN_IN_HO
LD_STATE 412h Servo Physical eot limit overrun occured in hold state
SRV_REEL_PHYSICAL_BOT_LIMIT_UNDERUN_IN_HO
LD_STATE 413h Servo Physical bot limit underrun occured in hold state
SRV_REEL_LP1_LIMIT_UNDERUN_IN_HOLD_STATE 414h Servo LP1 limit underrun in hold state
SRV_REEL_LP6_LIMIT_OVERRUN_IN_HOLD_STATE 415h Servo LP6 limit overrun in hold state
SRV_SEQ_PAST_EOT_REJ_INV_STATE_BETWEEN_E
OT_AND_PEOT 416h Servo LPOS is past EOT based on ratiometric EOT detection
SRV_REEL_INVALID_TASK_FOR_MESSAGE_RESPO
NSE 417h Servo Sender id not valid for sending a message to
SRV_STATEM_SEQUENCER_STACK_OVERFLOW 418h Servo Sequencer control stack overflowed.
SRV_SEQ_STACK_UNDERFLOW 419h Servo Sequencer control stack underflowed.
SRV_SEQ_PAST_EOT_REJ_INV_STATE_EXCEEDING
_PEOT 41Ah Servo Tape exceeds EOT per ratiometric calculation of position
SRV_MOVETAPE_UNEXPECTED_LPOS_NOTIFICATIO
N_IN_RAMP_UP_STATE 41Bh Servo An LPOS notification occured during ramp up
SRV_MOVETAPE_UNRECOGNIZED_COMMAND_IN_R
AMP_UP_STATE 41Ch Servo Unrecognized command detected at speed in ramp up state
SRV_STEP_HEAD_COULD_NOT_FIND_ANY_PES_DU
RING_HEAD_CALIBRATION 41Dh Servo No PES found during head offset calibration command.