Quantum LTO 4, User Manual

Page: 239 / 297

SRV_DIVIDER_TIMEOUT DCh Servo FW timed out waiting for hardware divider
SRV_SERVO_TIMEOUT DDh Servo Servo firmware time out
SRV_FIND_INDEX_FAILED DEh Servo Find drive motor index failed
SRV_CAL_SLOT_FAILED DFh Servo Calibrate slot command failed
SRV_GOTO_POINT_INVALID E0h Servo target point to close to ramp to or already past
SRV_SERVO_POWEROFF_FAILED E1h Servo servo did not acknowledge power off
SRV_REWIND_NOT_NECESSARY E2h Servo current tape position is at or before wrap point.
SRV_NOT_USED_8 E3h Servo
SRV_DIVIDER_OVERFLOW E4h Servo division overflow when using hardware divider.
SRV_MULTIPLY_ERROR E5h Servo overflow error in scaled int multiply routine.
SRV_WRONG_REEL_SELECT E6h Servo Wrong reel selected in rotate reel or stop reel command.
SRV_CMDPROC_UNDEFINED_SCRAMBLER_COMMA
ND E7h Servo Command sent from scrambler is not defined.
SRV_INVALID_MONITOR_MSG E8h Servo internal RTOS message unknown.
SRV_SELF_MONITOR_BUF_OVERFLOW E9h Servo fiq monitor to irq buffer overflow.
SRV_SELF_EVENT_BUF_OVERFLOW EAh Servo fiq event to irq buffer overflow.
SRV_RTOS_UNKNOWN EBh Servo unknown rtos error.
SRV_SEQ_TABLE_LOOKUP ECh Servo sequencer table look up error.
SRV_SEQ_NULL_FUNCTION_CALLED EDh Servo sequencer table function is null.
SRV_SEQ_UNEXPECTED_MESSAGE_RESPONSE EEh Servo response not expected for command.
SRV_SELF_ERROR_BUF_OVERFLOW EFh Servo fiq error buf to irq buffer overflow.
SRV_SEQ_NON_MECHANICAL_SCRAMBLER_COMM
AND F0h Servo non mechanical command received by sequencer.
SRV_SEQ_OUT_OF_RANGE_SCRAMBLER_COMMAN
D F1h Servo out of range command received by sequencer.
SRV_SELF_RTOS_BUF_OVERFLOW F2h Servo fiq rtos buffer to irq buffer overflow.
SRV_CMDPROC_UNDEFINED_TASK_FOR_COMMAND
_IN_BYPASS_MODE F3h Servo undefined task specified.
SRV_CMDTYPE_TABLE_INTEGRITY F4h Servo table integrity for command type or parameter table look
SRV_REEL_NO_TASK_SPECIFIED F5h Servo reel task received a message without a valid sender specified.
SRV_STACK_OVERFLOW F6h Servo stack overflow.
SRV_NO_SINECAL_DATA F7h Servo Sine calibration failed to find 0-xings.
SRV_BAD_SINECAL_DATA F8h Servo Sine calibration found invalid 0-xings.
SRV_NO_SINECAL_INDEX F9h Servo Sine calibration couldn't find index.
SRV_NO_LOADRCA_INDEX FAh Servo Sine RCA/RCB load couldn't find index.
SRV_PARAM_TABLE_INTEGRITY FBh Servo Table lookup not consistent with COMMAND_ENUM definitions.
SRV_PARPORT_SCRAMBLER_NOT_READY_IN_SEND
_RESPONSE FCh Servo Scrambler not ready to accept command.
SRV_PARPORT_UNDEFINED_CONDENSED_FORMAT FDh Servo Undefined scrambler condensed format.
SRV_CMDPROC_NO_TAPE_TO_EJECT FEh Servo Eject attempt rejected because there was no tape.
SRV_CMDPROC_REJECT_EJECT_INVALID_STATE FFh Servo Reject eject button due to invalid mechanical state.
SRV_STATUS_100 100h
Servo
SRV_CMD_REJECT 101h Servo Command rejected
SRV_CMD_ERROR 102h Servo Command error
SRV_CMD_ABORTED 103h Servo Command aborted
SRV_ALERT 104h Servo Servo Alert
SRV_MOVETAPE_ERROR_EOT_OVERRUN_DURING_
CRUISE_CONTROL 105h Servo Tape has gone past eot during cruise control state
SRV_MOVETAPE_ERROR_BOT_UNDERRUN_DURING
_CRUISE_CONTROL 106h Servo Tape has gone past bot during cruise control state
SRV_MOVETAPE_ERROR_EOT_OVERRUN_DURING_
RAMP_UP 107h Servo Tape has gone past eot during ramp up state
SRV_MOVETAPE_ERROR_BOT_UNDERRUN_DURING
_RAMP_UP 108h Servo Tape has gone past bot during ramp up state
SRV_INVALID_MARK_SELECT 109h Servo Invalid mode select in mark.c.
ECC_C2_ERROR 10Ah ECC
MIC_NO_STATUS 10Bh Medium
Auxiliary
Memory Fill Info.Word with this if there is no status to send.
MIC_PAGE_ID_BAD 10Ch Medium the PAGE ID value received is out of RANGE.