Quantum LTO 4, User Manual

Page: 257 / 297

SRV_OFF_TRACK 3CDh Servo tracking servo detected off track event
SRV_NO_PES_FOUND 3CEh Servo no valid PES event
SRV_VCM_SHOCK_ERROR 3CFh Servo tracking servo detected shock vibration error
SRV_TRACKING_TARGET_OUTRANGE 3D0h Servo tracking servo detected unreachable track error
SRV_TRACKING_SAMPLE_ERROR 3D1h Servo tracking servo detected asic sample error
SRV_TRACKING_COARSE_MOVE_ERROR 3D2h Servo tracking servo detected coarse stepper is out of position
SRV_TRACKING_UPDATE_MEM_ERROR 3D3h Servo tracking servo detected PES memory failure
SRV_MOVETAPE_RAMPDOWN_API_FAILED_IN_TRA
CKING_CMD_FAILED_HANDLER_IN_RAMP_UP_STAT
E 3D4h Servo Rampdown api call failed/rejected when called from tracking
command failed handl
SRV_MOVETAPE_TRACKING_CMD_FAILED_IN_RAM
P_UP_STATE 3D5h Servo Tracking command failed in ramp up state
SRV_CMDPROC_ROTATE_REEL_REJECTED_BECAU
SE_CART_LOADED 3D6h Servo Rotate reel command rejected because cartridge is loaded and
command is trying
SRV_CMDPROC_ROTATE_REEL_REJECTED_BECAU
SE_DRIVE_REEL_IS_OBSTRUCTED 3D7h Servo Rotate reel command rejected because reels are obstructed by
tape or a cartridge
SRV_CMDPROC_ROTATE_REEL_REJECTED_INVALI
D_REEL_SELECT 3D8h Servo Rotate reel command rejected because an invalid reel select was
given
SRV_CMDPROC_SET_DRIVE_STATE_COMMAND_RE
JECTED_STATE_OUT_OF_RANGE 3D9h Servo Set drive state command rejected because the drive state is out
of range.
SRV_STATEM_RECOVERY_COMMAND_REJECTED_D
RIVE_IN_UNKNOWN_STATE 3DAh Servo Recovery command rejected
SRV_TRKCNVT_MULTIPLY_ERROR_IN_TRACKING_C
ONVERT_FUNCTION 3DBh Servo Multiply error in tracking conversion function from ratio to dac
SRV_TRKCNVT_DIVIDE_ERROR_IN_TRACKING_CON
VERT_FUNCTION 3DCh Servo Divide error in tracking conversion function from dac to ratio.
SRV_STATEM_AUTOLOAD_COMMAND_REJECTED_I
NVALID_STATE 3DDh Servo Command rejected since the drive state was invalid (out of
range).
SRV_NOT_USED_OBSOLETE_2 3DEh Servo Command rejected since the drive state was invalid in eject
sequence
SRV_STATEM_PRE_EJECT_COMMAND_REJECTED_I
NVALID_STATE 3DFh Servo Command rejected since the drive state was invalid in pre-eject
sequence
SRV_STATEM_PRE_EJECT_COMMAND_REJECTED_
DRIVE_IN_UNKNOWN_STATE 3E0h Servo Command rejected
SRV_STATEM_AUTOLOAD_COMMAND_REJECTED_U
NKNOWN_STATE 3E1h Servo Command rejected
SRV_TRKCNVT_DAC_OUTPUT_EXCEEDED_LIMIT 3E2h Servo Calculated DAC tracking target greater than maximum input
SRV_TRKCNVT_DAC_OUTPUT_BELOW_MINIMUM_LI
MIT 3E3h Servo Calculated DAC tracking target less than minimum input
SRV_STEP_HEAD_EXPECTING_BOTTOM_SENSOR_H
IGH 3E4h Servo expecting SNS9 high
SRV_STEP_HEAD_EXPECTING_STOP_AFTER_BOTT
OM_SENSOR_HIGH 3E5h Servo expecting SNS9 low
SRV_STEP_HEAD_EXPECTING_BOTTOM_SENSOR_L
OW 3E6h Servo expecting stepper to halt after SNS9 high
SRV_STEP_HEAD_EXPECTING_STOP_AFTER_BOTT
OM_SENSOR_LOW 3E7h Servo expecting stepper to halt after SNS9 low
SRV_SZA_INTERFACE_BUSY 3E8h Servo interface to SZA chip busy for too long
SRV_SZA_FUNCTION_ACTIVE 3E9h Servo SZA read or write already in progress
SRV_SZA_REGISTER_INVALID 3EAh Servo request to read invalid SZA register number
SRV_SZA_READ_COUNT_TOO_LARGE 3EBh Servo amount of SZA read data exceeds buffer size
SRV_SZA_WRITE_COUNT_TOO_LARGE 3ECh Servo amount of SZA write data exceeds buffer size
SRV_SZA_WRITE_DATA_INVALID 3EDh Servo SZA write data contains invalid reg or chip ID
SRV_REEL_CARTDITHER_API_CALL_FAILED_INVALI
D_STATE 3EEh Servo Call to cartDither api failed
SRV_SERIAL_EEPROM_FAILED 3EFh Servo
SRV_SRV_RTOS_INVALID_TASK_ID_SPECIFIED 3F0h Servo invalid task specified in rtos wrapper function.
SRV_MOTOR_POWER_FAIL_1 3F1h
Servo no power to reel motor circuits on startup
SRV_MOTOR_POWER_FAIL_2 3F2h Servo no power to reel motor circuits after POR clear
SRV_MOTOR_POWER_FAIL_3 3F3h Servo no power to reel motor circuits after PF clear