![background image](http://html1.mh-extra.com/html/quantum/lto-4/lto-4_user-manual_3834212273.webp)
ALID_STATE range).
SRV_CMDPROC_CMD_REJECT_SEQUENCER_BUSY_
AND_BUFFER_FULL
613h
Servo
Command rejected since the sequencer was processing an error
and the polled buff
SRV_CANNOT_INSERT_INTO_LPOS_NOTIFY_TABLE_
UNTIL_SCR_AND_WP_FOUND_LP1
614h
Servo
LPOS values in the notification table are dependent on CM_LP1
and WP_LP1.
SRV_LPOS_ROLLOVER_DETECTED_FROM_CM_PHY
S_LP1
615h
Servo
Calc phy LP7 from CM phys LP1 is greater then LTO spec
SRV_LPOS_ROLLOVER_DETECTED_FROM_WP_CAL
C_PHYS_LP1
616h
Servo
Calc phy LP7 from WP calc phys LP1 is greater then LTO spec
SRV_LPOS_TOP_SERVO_AND_BOTTOM_SERVO_CA
LC_LP1_NOT_WITHIN_TOLERANCE
617h
Servo
The LP1 value calc for top servo didn't match the LP1 value calc
for the bottom
SRV_REEL_MOT_PWR_FAIL_DETECTED
618h
Servo
12 volt power reset detected
SRV_REEL_MOT_EXCESSIVE_CURRENT_DEMAND_D
ETECTED
619h
Servo
Excessive current detected on motor
SRV_FINDZERO_TIME_OUT 61Ah
Servo
Time
out occured waiting for servo response
SRV_FINDZERO_STATE_VARIABLE_OUT_OF_RANGE 61Bh
Servo
Find zero wrap state variable out of range.
SRV_FINDZERO_COARSE_OR_APPROACHING 61Ch
Servo
Find zero wrap coarse or approaching api rejected call.
SRV_FINDZERO_INDEX_SETUP_API_REJECT
61Dh
Servo
Find zero wrap index setup api rejected call.
SRV_FINDZERO_INDEX_HOME_API_REJECT 61Eh
Servo
Find zero wrap index home api rejected call.
SRV_FINDZERO_HOME_DRIVE_REEL_API_REJECT
61Fh
Servo
Find zero wrap home drive reel api rejected call.
SRV_FINDZERO_APPROACHING_API_REJECT 620h
Servo
Find
zero wrap approaching zero api rejected call.
SRV_FINDZERO_TOO_MANY_RETRIES_AFTER_COA
RSE_MOTION
621h
Servo
Find zero wrap coarse exceeded coarse motion retries.
SRV_FINDZERO_TOO_MANY_RETRIES_AFTER_COM
PLETE
622h
Servo
Find zero wrap retries exceeded after completion.
SRV_CMDPROC_FIND_INDEX_FAILED_WRITING_TO_
LINEAR_COUNTER_API_BUSY
623h
Servo
Reset linear counter to remember the aligned slot position
SRV_CMDPROC_LINEAR_COUNTER_NOT_RECORDE
D_PREVIOUSLY
624h
Servo
Linear counter not reset with RECORD ALIGNED SLOT
command prior to this command
SRV_SEQ_POWER_ON_INIT_FAILED_WRITING_TO_LI
NEAR_COUNTER_API_BUSY
625h
Servo
Reset linear counter failed during power on recovery
SRV_CMDPROC_INVALID_STATE_FOR_RAMP_HEAD
_COMMAND
626h
Servo
Ramp head command rejected
SRV_CMDPROC_TAPE_NOT_MOVING_FOR_RAMP_H
EAD_COMMAND
627h
Servo
Ramp head command rejected
SRV_CMD_INVALID_HEAD_POSITION_SPECIFIED_IN
_CHANGE_TRACKING_MODE
628h
Servo
Head position not a valid tracking head position
SRV_CMD_INVALID_HEAD_POSITION_SPECIFIED_IN
_WRAP_RESTART_TRACKING
629h
Servo
Head position not a valid tracking head position for restart
tracking
SRV_MOVETAPE_SET_LC_NOTIFICATION_FAILED 62Ah Servo Attempt
to set linear counter mark failed since already past
point.
SRV_CMDPROC_REJ_TAPE_NOT_READY 62Bh
Servo
Tape ready for retension
SRV_STEP_HEAD_EXPECTING_MOVING_UP_WITH_A
DDED_HYSTERESIS_AFTER_REFERENCE_SENSOR_
HIGH
62Ch
Servo
Expecting moving up with added hysteresis after reference
sensor high.
SRV_CMD_INVALID_COMMAND_CALLED_SEQUENC
E_IS_NULL
62Dh
Servo
Invalid command called or invalid message sent to sequencer
SRV_TIMEOUT_DURING_HEAD_STEPPER_STOPPING
_AFTER_SEARCHING_FOR_SERVO_BAND
62Eh
Servo
Timeout during head stepper stopping after searching for servo
bundle
SRV_TIMEOUT_DURING_HEAD_STEPPER_MOVING_
UP_WITH_ADDED_HYSTERESIS_AFTER_REFERENC
E_SENSOR_HIGH
62Fh
Servo
Timeout during head stepper moving up with added hysteresis
after reference sens
SRV_STEP_HEAD_EXPECTING_SEARCHING_FOR_SE
RVO_BAND
630h
Servo
Expecting searching for servo bundle
SRV_STEP_HEAD_EXPECTING_HYSTERESIS_BEFOR
E_SEARCHING_FOR_SERVO_BAND_IN_OTHER_DIRE
CTION
631h
Servo
Expecting hysteresis before searching for servo bundle in other
direction
SRV_STEP_HEAD_EXPECTING_SEARCHING_FOR_SE
RVO_BAND_IN_OTHER_DIRECTION
632h
Servo
Expecting searching for servo bundle in other direction
SRV_STEP_HEAD_EXPECTING_STOPPING_AFTER_F
AILING_SEARCH_FOR_SERVO_BAND_IN_OTHER_DI
633h
Servo
Expecting stopping after failing search for servo bundle in other
direction
Summary of Contents for LTO 4
Page 1: ......