Index
Positioning via digital I/Os
312
192-120101 N11 C3I11T11 November 2007
Motor Selection • 77
Mounting and dimensions C3H • 65
Mounting and dimensions C3MP/C3M • 64
Mounting and dimensions Compax3S300V4 •
63
Mounting distances, air currents
Compax3H050V4 • 66
Mounting distances, air currents
Compax3H090V4 • 66
Mounting distances, air currents
Compax3H1xxV4 • 67
N
Noise • 126
Nominal point • 130
Nominal point data • 123
Non-linearities and their effects • 208
Notch filter • 169
Note: • 71
O
Offset alignment • 193
Open/Closed Loop frequency response
measurement • 206
Operating and status field • 219
Operating modes • 97
Operator control module BDM • 284
Optimization • 108
Optimization parameter Advanced • 161
Optimization window • 109
Optimize motor reference point and switching
frequency of the motor current • 78
Order code • 244
Order code device
Compax3 • 245
Order code for mains module
Compax3MP • 246
Oscillating plant • 137
Oscilloscope operating mode switch: • 113
Other • 169
Other motor • 134
Other settings • 217
Overview of motor cables • 262
Overview of the user interface • 211
P
Packaging, transport, storage • 11
Parameterization by 3 objects. • 170
Parker Motor • 134
Parker servo motors • 251
PC - Compax3MP (mains module) • 54
Permissible braking pulse power
BRM04/01 with C3S150V2 • 274
BRM04/01 with C3S300V4 • 275
BRM04/02 with C3S150V2 • 275
BRM04/02 with C3S300V4 • 276
BRM04/03 with C3S300V4 • 276
BRM05/01 with C3S063V2 • 273
BRM05/01 with C3S075V4 • 273
BRM05/02 with C3S075V4 • 274
BRM08/01 with C3S015V4 / C3S038V4 • 271
BRM08/01 with C3S025V2 • 271
BRM09/01 with C3S100V2 • 272
BRM10/01 with C3S150V4 • 272
BRM11/01 with C3H0xxV4 • 277
BRM12/01 with C3H1xxV4 • 277
BRM13/01 with C3MP10D6 • 278
BRM14/01 with C3MP10D6 • 278
Permissible braking pulse powers of the
braking resistors • 269
Plug and pin assignment C3H • 46
Plug assignment Compax3S0xx V2 • 26, 27,
28, 29, 53, 56
Position control • 212
Position mode in reset operation • 100
Positioning • 96
Positioning window - Position reached • 93
Postition loop • 148
Power supply • 28
Power supply connector X1 for 3AC
400VAC/480VAC-C3S devices • 31
Power supply plug X1 for 1 AC
230VAC/240VAC devices • 28
Power supply plug X1 for 3AC
230VAC/240VAC devices • 29
Power supply voltage DC C3H • 51
Prerequisites • 196
Prerequisites for the automatic commutation •
166
Principle • 190
Proceeding during configuration, setup and
optimization • 119
Proceeding during controller optimization • 175
Process of the automatic determination of the
load characteristic value (load identification)
• 191
ProfileViewer for the optimization of the motion
profile • 229
P-TE - Symbol • 139
P-term KV position loop • 149
Q
Quality of different feedback systems • 125
R
Ramp upon error / deenergize • 92
Recommendations for preparing the modem
operation • 241
Reduction of the current ripple • 133
Ref X11 • 292
Reference point 1
higher velocity at reduced torque • 131
Reference point 2
Increased torque thanks to additional cooling •
132
Relevant appication parameters • 132
Remote diagnosis via Modem • 237
Repeat count • 101
Resolution • 126
Resolver • 56
Resolver / Feedback (connector X13) • 56
Resolver cable • 260
Resonance points and their causes • 226
response • 143