Optical Systems Design OSD2512 User Manual Download Page 364

Page: 364 / 401

OPTICAL SYSTEMS DESIGN

DOC ID: 10118101

OSD2512 OPERATOR MANUAL

PAGE 364

Priority

is the Layer 2 priority to be used for the specified application type. One of the eight

priority levels (0 through 7).

DSCP

is the DSCP value to be used to provide Diffserv node behaviour for the specified

application type as defined in IETF RFC 2474. Contain one of 64 code point values (0 through
63).

Auto-negotiation

identifies if MAC/PHY auto-negotiation is supported by the link partner.

Auto-negotiation status

identifies if auto-negotiation is currently enabled at the link partner.

Auto-negotiation

is supported and

Auto-negotiation status

is disabled, the 802.3 PMD

operating mode will be determined the operational MAU type field value rather than by auto-
negotiation.

Auto-negotiation Capabilities

shows the link partners MAC/PHY capabilities.

Buttons

Auto-refresh

: Check this box to refresh the page automatically. Automatic refresh

occurs every 3 seconds.

: Click to refresh this page

Summary of Contents for OSD2512


















































































































































































































































































































































































































Search results

Summary of Contents for OSD2512

Reviews:

Related manuals for OSD2512

Brands by name

Popular brands

Optical Systems Design OSD2512, User Manual

Search results

Summary of Contents for OSD2512

Reviews:

Related manuals for OSD2512

Brands by name

Popular brands