manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 170

6-1

Power ON

This section provides Power ON details.

6-1-1

Power ON Using the Power Button

Start condition: Power is supplied to the Box PC and the Box PC is OFF.

1

Press the power button and release within 1 second.
Refer to 

3-3 Power Button

 on page 3-9 for the power button location.

The Box PC starts and the PWR LED will turn ON.

2

Wait until the PWR LED is ON and verify that the ERR LED is OFF.

The Box PC is ON and the Operating System, if installed, starts.

6-1-2

Power ON Using the Power ON/OFF Input

Start condition: Power is supplied to the Box PC and the Box PC is OFF.

1

Supply an input signal to pins 3 and 4 of the I/O connector.
The input signal must remain ON for a minimum of 60 ms and a maximum of 750 ms to be
correctly detected by the Box PC.
The Box PC starts and the PWR LED will turn ON.

2

Wait until the PWR LED is ON and verify that the ERR LED is OFF.

The Box PC is ON and the Operating System, if installed, starts.

Additional Information

• Refer to 

4-2-2 I/O Connector Specifications

 on page 4-19 for connector specifications.

• Refer to 

5-4-4 Wire the I/O Connector

 on page 5-36 for wiring details.

6-1-3

Auto Power ON

The Box PC can be configured to start up when power is supplied to the power connector.
The 

Power Loss Control

 BIOS setting controls this behavior.

Set the Power Loss Control setting to 

Turn ON

 to activate the Auto Power ON function.

Additional Information

Refer to 

A-1 BIOS

 on page A-2 for BIOS details.

6 Operating Procedures

6-2

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands