Home
/
Omron
/
SYSMAC NY Series
/
Hardware User Manual

Omron SYSMAC NY Series, Hardware User Manual

Share

Page: 134 / 260

Omron SYSMAC NY Series Hardware User Manual Download Page 134

Hardware Arrangement

The coils and contacts in electromagnetic contacts and relays in an external circuit are sources of
noise. Do not install them close to the Box PC. Locate them at least 100 mm away from the Box PC.

Example of Arrangement in Panel

AC I/O

device

Terminal block

DC I/O

device

OMRON

product

Wire Layout for the Power Supply

Observe the following points when wiring the power supply system.
• Separate the Box PC power supply from the I/O device power supply and install a noise filter near

the Box PC power supply feed section.

• Use an isolating transformer to significantly reduce noise between the Box PC and the ground. In-

stall the isolating transformer between the Box PC power supply and the noise filter, and do not
ground the secondary coil of the transformer.

• Keep the wiring between the transformer and the Box PC as short as possible, twist the wires well,

and keep the wiring separate from high-voltage and power lines.

Unit power supply for Omron product

I/O power supply for Omron product

Power Supply System Diagram

Power circuits

Power supply for general operations circuits

Outlet (for peripheral devices)

I/O power supply for Omron product

Noise
filter

5 Installation

5-20

NY-series Industrial Box PC Hardware User's Manual (W553)

«
...
132
133
134
135
136
...
»

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands