Omron SYSMAC NY Series Hardware User Manual Download Page 88

Page: 88 / 260

4-1-8

PCIe Card Specifications

The PCI Express (PCIe) Card slot of the Industrial Box PC accepts various cards for specific hardware
needs.

Ensure that, according to the PCIe hardware specifications, the indent

is present in the PCIe Card.

The PCIe Card specifications depend on the CPU and thus on the product configuration.

Additional Information

• Refer to

1-4 Product Configuration Box PC

on page 1-5 for product configuration details.

• Refer to

1C-

1 PCIe Card Slot Specifications

on page 4-14 for details.

• Refer to

1E-

1 PCIe Card Slot Specifications

on page 4-15 for details.

• Refer to

17-

1 PCIe Card Slot Specifications

on page 4-15 for details.

• Refer to

2C-

1 PCIe Card Slot Specifications

on page 4-15 for details.

• Refer to

25-

1 PCIe Card Slot Specifications

on page 4-16 for details.

• Refer to

35-

1 PCIe Card Slot Specifications

on page 4-16 for details.

1C-

1 PCIe Card Slot Specifications

The table below provides PCIe Card slot details for Industrial Box PCs with an Intel

Celeron

2980U

CPU.

Item

Specifications

Configuration

X1 (1 lane) up to Gen 2

Card height

Standard height cards, 4.20 inches (106.7 mm)

Card length

Half-length cards, 6.6 inches (167.65 mm)

Power consumption

5 W max.

Maximum current

1.5 A with 3.3 VDC, 0.5 A with 12 VDC

*1.

Low profile cards, 2.536 inches (64.4 mm) are not supported.

4 Specifications

4-14

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Search results

Summary of Contents for SYSMAC NY Series

Reviews:

Brands by name

Popular brands

Omron SYSMAC NY Series, Hardware User Manual

Search results

Summary of Contents for SYSMAC NY Series

Reviews:

Brands by name

Popular brands