Omron SYSMAC NY Series Hardware User Manual Download Page 43

Page: 43 / 260

Hardware

This section provides an overview of the hardware of the Industrial Box PC.

3-1 Layers and Components ............................................................................... 3-3

3-1-1

Cooling Layer.................................................................................................. 3-4

3-1-2

Base Layer...................................................................................................... 3-5

3-1-3

Expansion Layer (Optional) ............................................................................ 3-6

3-2 LED Indicators................................................................................................ 3-7

3-2-1

PWR LED Indicator......................................................................................... 3-7

3-2-2

ERR LED Indicator ......................................................................................... 3-8

3-2-3

HDD LED Indicator ......................................................................................... 3-8

3-2-4

RUN LED Indicator ......................................................................................... 3-8

3-3 Power Button.................................................................................................. 3-9

3-4 Connectors ................................................................................................... 3-10

3-4-1

Power Connector .......................................................................................... 3-10

3-4-2

I/O Connector ............................................................................................... 3-10

3-4-3

USB Connectors ............................................................................................3-11

3-4-4

Ethernet Connectors..................................................................................... 3-12

3-4-5

DVI Connector .............................................................................................. 3-12

3-4-6

RS-232C Connector (Optional)..................................................................... 3-13

3-4-7

DVI-D Connector (Optional).......................................................................... 3-13

3-4-8

NY Monitor Link Connector (Optional).......................................................... 3-14

3-4-9

Ethernet Connector (Optional)...................................................................... 3-15

3-5 SD Memory Card Slot .................................................................................. 3-16

3-6 CFast Card Slot (Optional) .......................................................................... 3-17

3-7 Drive Bays..................................................................................................... 3-18

3-8 PCIe Card Slot .............................................................................................. 3-19

3-9 Spare Parts ................................................................................................... 3-20

3-9-1

Battery .......................................................................................................... 3-20

3-9-2

Fan Unit ........................................................................................................ 3-20

3-9-3

Accessory Kit ................................................................................................ 3-21

3-10 Optional Hardware ....................................................................................... 3-22

3-10-1

Mounting Brackets ........................................................................................ 3-22

3-10-2

SD Memory Cards ........................................................................................ 3-23

3-10-3

USB Flash Drives ......................................................................................... 3-23

3-10-4

CFast Cards.................................................................................................. 3-24

3-10-5

HDD and SSD Storage Devices ................................................................... 3-25

3-10-6

DVI Cables.................................................................................................... 3-26

3-1

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Search results

Summary of Contents for SYSMAC NY Series

Reviews:

Brands by name

Popular brands

Omron SYSMAC NY Series, Hardware User Manual

Search results

Summary of Contents for SYSMAC NY Series

Reviews:

Brands by name

Popular brands