manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 92

4-2

Connector Specifications

This section provides the Connector Specifications of the Industrial Box PC.

4-2-1

Power Connector Specifications

The power supply connector is locked when inserted to prevent unintentional disconnection.
The connector can only be inserted the correct way.
The connector is a Phoenix Contact type SPC5/2-STCL-7.62 BK (1711708).
The Box PC provides protection against reverse polarity.

2

1

The pin layout represents the power connector on the Box PC.

Pin

Description

1

24 VDC

2

0 VDC

Item

Specifications

Conductor isolation rating

90°C

Termination rating

90°C

Additional Information

• Refer to 

5-4-3 Wire the Power Connector

 on page 5-33 for wiring details.

• Refer to 

5-4-2 Ground

 on page 5-26 for grounding details.

4 Specifications

4-18

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands