manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 76

4-1

General Specifications

This section provides general specifications of the Industrial Box PC.

4-1-1

Dimensions and Weight

The following table provides specification details on dimensions and weights.

Z

Y

X

Model

Specifications

Model ID 

*1

 

*2

Model details

Mount details

Width X

Depth Y 

*3

Height Z

Weight

•

NYB1C-

£

1

•

NYB1E-

£

1

•

NYB17-

£

1

•

NYB25-

£

1

•

With Expansion
layer

•

With Cooling
layer with re-
movable cover

Not mounted

282 mm

200 mm

89 mm

3.8 kg

Book mount

319 mm 

*4

211 mm

96 mm 

*4

4.2 kg

Wall mount

282 mm

245 mm 

*4

92 mm

3.9 kg

•

NYB2C-

£

1

•

NYB35-

£

1

•

With Expansion
layer

•

With Cooling
layer with non-
removable cover

Not mounted

282 mm

200 mm

73 mm

3.0 kg

Book mount

319 mm 

*4

211 mm

80 mm 

*4

3.3 kg

Wall mount

282 mm

245 mm 

*4

76 mm

3.1 kg

4 Specifications

4-2

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands