Home
/
Omron
/
SYSMAC NY Series
/
Hardware User Manual

Omron SYSMAC NY Series, Hardware User Manual

Share

Page: 131 / 260

Omron SYSMAC NY Series Hardware User Manual Download Page 131

High Temperatures

Use the following cooling methods as required, taking into account the ambient temperature and the
amount of heating inside the panel.



Natural Cooling

Natural cooling relies on natural ventilation through slits in the panel, rather than using cooling devi-
ces such as fans or coolers. When using this method, observe the following points.
• Do not install the Box PC at the top of the panel, where hot air tends to stagnate.
• To provide ventilation space above and below the Box PC, leave sufficient distance from other

devices, wiring ducts, etc.

• Do not mount the Box PC in the wrong direction (e.g., vertically or upside down). Doing so may

cause abnormal heating in the Box PC.

• Do not install the Box PC directly above any heat-generating equipment, such as heaters or

transformers.

• Do not install the Box PC in a location exposed to direct sunlight.

Natural Cooling

OMRON
product

OMRON
product



Forced Ventilation

Forced ventilation with a fan in the top of the control cabinet.

Air filter

Fan

Forced Ventilation Method

OMRON
product

OMRON
product



Forced Air Circulation

Forced circulation with a fan inside the closed control cabinet.

5 Installation

5-17

NY-series Industrial Box PC Hardware User's Manual (W553)

5-3 Mount

5

5-3-3

T

emperature

«
...
129
130
131
132
133
...
»

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands