manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 181

7-2-3

Replace the Fan Unit

The fans are mounted in the Fan Unit.
Use the following procedure to replace the Fan Unit.

Precautions for Safe Use

If the replacement Fan Unit has been stored over 6 months then check the performance of the
Fan Unit after replacement.

Additional Information

Refer to 

3-9-2 Fan Unit

 on page 3-20 for the model.

1

Power OFF the Box PC.

2

Remove the Cover of the Box PC.

Additional Information

Refer to 

7-2-2 Remove the Cover

 on page 7-6 for the cover removal procedure.

3

Disconnect the Fan Connectors from the board.

7 Maintenance

7-7

NY-series Industrial Box PC Hardware User's Manual (W553)

7-2
 Corrective Maintenance

7

7-2-3

 Replace the Fan Unit

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands