manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 122

8

Mount the drive cover.
The lock lever will click when closed correctly.

9

Finalize the drive installation when the Box PC installation is completed.
• For a drive that requires an operating system:

1) Install an operating system

2) Power OFF and then Power ON

3) Ensure the drive is functional and confirm normal operation.

If required set the drive as boot disk in the BIOS settings.
Refer to 

A-1 BIOS

 on page A-2 for boot priority settings.

• For storage drives:

1) Ensure the drive is functional and confirm normal operation.

2) For a Box PC with a Windows operating system:

If the storage drive should be visible in Windows but it is not visible then that drive needs
to be allocated.
Refer to 

3-1-3 Expansion Layer (Optional)

 on page 3-6 for details on the visiblity per stor-

age drive.

The drive is installed and functional.

5 Installation

5-8

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands