manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 227

BIOS - Save & Exit

Provides the possibility to leave the BIOS with or without saving changes and to create or restore a set
of User Defaults.

Save & Exit Parameters: 

Disabled

.

•

Save Changes and Exit

Changed settings are saved and the Operating System starts with the changed settings.

•

Discard Changes and Exit

Changed settings are not saved and the Operating System starts with the unchanged settings.

•

Save Changes and Reset

Changed settings are saved and the Box PC restarts using the changed settings.

•

Discard Changes and Reset

Changed settings are not saved and the Box PC restarts with the unchanged settings.

•

Save Changes

Changed settings are saved and the BIOS setup stays open.

•

Discard Changes

Changed settings are reverted to their last saved values and the BIOS setup stays open.

•

Restore Defaults

Revert all BIOS settings to factory default.

•

Save as User Defaults

Saves the BIOS values as a User Defaults set.

•

Restore User Defaults

Restores the User Defaults set to the BIOS.

Appendices

A-29

NY-series Industrial Box PC Hardware User's Manual (W553)

A-1 BIOS

A

A-1-3 BIOS for 6

th

 generation CPUs

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands