manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 191

4

Push the notch 

1

 at the bottom of the Card Support up and rotate 

2

 the Card Support.

Slide the Card Support 

3

 away from the card to create space and to remove it.

2

1

3

5

Grip the Card Clip 

A

 on the sides 

1

. Pull the middle of the Card Clip to unlock it 

2

 and

remove it 

3

 from the PCIe Drawer.

Caution

When installing or removing a PCIe card, ensure to grip the Card Clip
on the sides to prevent contact with the sharp edges of the sheet metal
frame tab. Injury may result.

3

2

1

B

A

A

 Card Clip

B

 Sheet metal frame tab

7 Maintenance

7-17

NY-series Industrial Box PC Hardware User's Manual (W553)

7-2
 Corrective Maintenance

7

7-2-6

 Replace the PCIe Card

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands