manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 229

BIOS - Advanced

This section provides Advanced BIOS information for 7

th

 generation CPUs.

Changeable BIOS Advanced parameters and their factory default values:

Item

Default / Remark

Intel RC ACPI Settings PTID Support

Disabled

PECI Access Method

Direct I/O

Native PCI Express Support

Enabled

Native ASPM

Disabled

BDAT ACPI Table Support

Disabled

Wake system from S5

Disabled

ACPI Debug

Disabled

Low Power S0 Idle Capability

Disabled

Lpit Recidency Counter

SLP S0

PCI Delay Optimization

Disabled

ZpODD Support

Disabled

CPU

SW Guard Extensions (SGX)

Software Controlled

Select Owner EPOCH input type

No Change in Owner
EPOCHs

CPU Flex Ratio Override

Disabled

Hardware Prefetcher

Enabled

Adjacent Cache Line Prefetch

Enabled

Intel (VMX) Virtualization Technology

Enabled

PECI

Enabled

Active Processor Cores

All

Hyper-Threading 

*1

Enabled

BIST

Disabled

JTAG C10 Power

Disabled

AP threads Idle Manner

MWAIT Loop

AP threads Handoff Manner

MWAIT Loop

AES

Enabled

MachineCheck

Enabled

MonitorMWait

Enabled

Intel Trusted Execution Technology 

*1

Disabled

Reset AUX Content 

*1

No

Flash Wear Out Protection

Disabled

Debug Interface

Disabled

Debug Interface Lock

Enabled

Processor trace memory allocation

Disabled

CPU SMM Enhance-
ment

SMM Code Access Check

Enabled

SMM Use Delay Indication

Enabled

SMM Use Block Indication

Enabled

FCLK Frequency for Early Power On

Normal (800 Mhz)

Three Strike Counter

Enabled

Voltage Optimization

Auto

Appendices

A-31

NY-series Industrial Box PC Hardware User's Manual (W553)

A-1 BIOS

A

A-1-4 BIOS for 7

th

 generation CPUs

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands