Omron SYSMAC NY Series Hardware User Manual Download Page 164

Page: 164 / 260

Additional Information

• The default

Input sensitivity setting

Standard voltage sensitivity

and this is correct.

Do not set this parameter to

Low voltage sensitivity

. Doing so can cause a system malfunc-

tion when switching to battery mode.

• The UPS Setting Utility can not be used when the Power Attendant Lite Utility is active.

To use the UPS Setting Utility:
1. Right-click the Power Attendant Lite Utility icon and select Agent Stop.
2. Use the UPS Setting Utility.
3. Right-click the Power Attendant Lite Utility icon and select Agent Start.

5-8-2

Connect UPS Using the I/O Connector

The I/O connector of the Industrial Box PC:
• receives the power status of the UPS with the UPS Mode Input when the Box PC has a Windows

operating system. For other operating systems this input is not functional.

• indicates the power status of the Box PC to the UPS with the Power Status Output.

Additional Information

• A UPS connection using the I/O connector is only possible for a Box PC with a Windows op-

erating system. For all other operating systems use the USB connector to connect the UPS.
Refer to

5-8-1 Connect UPS Using the USB Connector

on page 5-48 for details.

• The Box PC does not react automatically to the UPS Mode Input.

A custom software program is required

to shut down the Box PC when needed.

UPS Drivers and the required software is available.
• For Box PCs with Windows 10 or Windows 7 preinstalled:

• Drivers for the S8BA UPS are pre-installed
• Installation files and manual for the UPS Settings Utility are availabe in the installer directory

D:\OMRON-NY\Installers\UPS Settings Utility

• For all other Box PCs following software can be downloaded:

• Drivers for the S8BA UPS from this OMRON website.
• Installation files and manual for the UPS Settings Utility (Windows only) from this OMRON web-

site.

Precautions for Safe Use

• Always use the recommended uninterruptible power supply (UPS) to prevent data loss and

other system file integrity issues caused by unexpected power interruption.

• Use an Omron S8BA UPS with the correct revision number to prevent improper system shut-

down.

• Correctly perform wiring and setting, and ensure that the shutdown by the UPS can be exe-

cuted.

Follow the steps below to connect the S8BA UPS to the I/O connector of the Box PC and to configure
it correctly.
Refer to

5-4-4 Wire the I/O Connector

on page 5-36 for I/O Connector details.

Ensure the revision number of the UPS is correct.
Refer to

3-10-11 UPS

on page 3-31 for more information.

5 Installation

5-50

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Search results

Summary of Contents for SYSMAC NY Series

Reviews:

Brands by name

Popular brands

Omron SYSMAC NY Series, Hardware User Manual

Search results

Summary of Contents for SYSMAC NY Series

Reviews:

Brands by name

Popular brands