Home
/
Omron
/
SYSMAC NY Series
/
Hardware User Manual

Omron SYSMAC NY Series, Hardware User Manual

Share

Page: 178 / 260

Omron SYSMAC NY Series Hardware User Manual Download Page 178

7-2

Corrective Maintenance

Corrective maintenance covers all actions to correct problems that cause downtime.

WARNING

Do not attempt to disassemble, repair, or modify the product in any
way. Doing so may result in malfunction or fire.

Contact your local OMRON representative if the corrective maintenance actions did not solve the
problem.

7-2-1

Warning and Error Messages

Warning and Error messages are provided by the Industrial Box PC when there is a potential problem
that may cause downtime. This section provides details about these messages.
Warning messages inform you about a situation that will lead to downtime of the Industrial Box PC.
Error messages inform you about what caused the downtime of the Industrial Box PC.

The following message channels are available.

LED Indicators

The ERR LED indicator provides information on warnings and errors.

Industrial PC Support Utility

The Industrial PC Support Utility provides information on warnings and errors.

The Industrial PC Support Utility indicates:
• Internal temperature above setting

Check the status of the Fan Unit and check the ambient conditions.

• Low revolution speed of the Fan Unit

• Check for excessive dust on the fans and in the Fan Unit.
• If required replace the Fan Unit.

• Low battery status

Replace the battery.

Windows Action Center

The Windows Action Center provides information on Windows related warnings and errors.

The Windows Action Center indicates security and maintenance issues.
Some examples:
• Virus protection (Important)

7 Maintenance

7-4

NY-series Industrial Box PC Hardware User's Manual (W553)

«
...
176
177
178
179
180
...
»

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands