manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 151

Pin

Description

Internal Circuit Details

3

Power ON Input

The Power ON Input and the UPS Mode Input are bi-di-
rectional and isolated. Each input can be wired as sinking
(NPN) or sourcing (PNP). Wire these according to the
output device connected to the inputs.

4
5

UPS Mode Input

6

Additional Information

• Refer to 

4-2-2 I/O Connector Specifications

 on page 4-19 for I/O connector specifications.

• Refer to 

I/O Connector Power Status Output Details

 on page 4-21 for power status output de-

tails.

• Refer to 

3-10-11 UPS

 on page 3-31 for UPS information.

5 Installation

5-37

NY-series Industrial Box PC Hardware User's Manual (W553)

5-4
 W
ire

5

5-4-4

 Wire the I/O Connector

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands