manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 148

Power Connector Wiring Materials

Use the power supply connector that was supplied to connect the power supply to the Industrial Box
PC.
• Select power supply conductors with consideration to the voltage drop and heat generation for the

cable length at the installation environment.

• Always use twisted wires to minimize the occurrence of electrical disturbance.
• Recommended power supply conductor sizes are provided in the table.

Wire type

Conductor cross-section

Solid conductor

0.5 to 10 mm

2

Flexible conductor

0.5 to 6 mm

2

Flexible conductor, with ferrule and no plastic sleeve

0.5 to 6 mm

2

Flexible conductor, with ferrule and plastic sleeve

0.5 to 4 mm

2

Minimum AWG according to UL/cUL

20

Maximum AWG according to UL/cUL

8

• Power Supply Connector

DC Power Supply

The OMRON S8VK-series power supply is recommended for use with the Industrial Box PC.

Additional Information

• Refer to 

3-10-10 Power Supply

 on page 3-30 for more information.

• Refer to 

4-1-3 Power Consumption Specifications

 on page 4-4 for power consumption details.

5 Installation

5-34

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands