manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 174

6-4

React to Windows Messages

Windows uses the Windows Action Center icon 

A

 in the system tray area 

B

 of Windows to present

Warnings and Errors.

A

B

A

B

Windows 10

Windows 7

Check the Windows Action Center icon for a Warning or Error symbol.
A Warning or Error symbol displayed on the Windows Action Center icon indicates a Windows mes-
sage.
To react to a Windows message:

1

Open the Windows Action Center.
• For Windows 10: Click the Windows Action Center icon.
• For Windows 7: Rightclick the Windows Action Center icon and select 

Open Action Center

from the pop-up window.

A pop-up window will appear.

Windows 10

Windows 7

2

Read the message available in the window.

3

Perform the actions until each Warning or Error is resolved.

The Windows messages for the Industrial Box PC are resolved.

6 Operating Procedures

6-6

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands