manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 184

3

Lift the battery 

1

 from the compartment.

4

Disconnect the battery from the battery connector 

2

.

2

1

5

Connect the new battery to the battery connector.

6

Place the new battery in the Box PC.
Ensure the wires are at the side of the battery and not on top of the battery. If the wires are on
top of the battery this might make closing and opening the cover more difficult.

7

Write the next date of replacement on the label at the inside of the cover.

Additional Information

Refer to 

3-9-1 Battery

 on page 3-20 for lifetime of the battery.

8

Mount the cover.

9

Remove the power connector for at least 3 seconds to reset the battery warning.

10

Power ON the Box PC.

11

Check the Date and Time in the operating system.
Correct the Date and Time if this is required.

The battery is replaced and the alarm is reset.

7 Maintenance

7-10

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands