manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 146

Ground Connection Details

This section provides details about the ground connection.
Use the functional ground terminal on the mounting bracket(s) to ground your Industrial Box PC.

The washers and nut 

C

 are supplied with the bracket(s).

Refer to 

Items Supplied with the Brackets

 on page 5-4 for details.

Book Mount

7

B

A

C

Mount the ground connection wire 

B

 to the functional ground terminal 

A

 using the washers and nut

C

. Tighten the nut with a torque of 1.2 N·m max.

Refer to 

5-3-8 Book Mount Procedure

 on page 5-24 for book mounting details.

Wall Mount

7

B

A

C

Mount the ground connection wire 

B

 to the functional ground terminal 

A

 using the washers and nut

C

. Tighten the nut with a torque of 1.2 N·m max.

Refer to 

5-3-9 Wall Mount Procedure

 on page 5-25 for wall mounting details.

5 Installation

5-32

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands