manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 149

Power Connector Wiring Procedure

Use the following procedure to wire the power connector.

1

Ensure the power connector is not connected to the Box PC.

2

Remove the sheath from the power supply wires.

7 mm

Precautions for Safe Use

Observe the following precautions to prevent broken wires.
• When you remove the sheath, be careful not to damage the conductor.
• Connect the conductor without twisting the wires.
• Do not weld the conductors. Doing so may cause the wires to break with vibration.

3

Insert a screwdriver in the small opening above the cable opening 

1

 to unlock the cable entry

and then push the wire all the way to the back of the cable opening 

2

.

2

1

1

2

Pin

Description

1

24 VDC

2

0 VDC

4

Remove the screwdriver.

Do not apply stress to the cable after you have connected the wires.

5 Installation

5-35

NY-series Industrial Box PC Hardware User's Manual (W553)

5-4
 W
ire

5

5-4-3

 Wire the Power Connector

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands