manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 22

• Do not attempt to remove or touch the fan unit while the product is powered ON or immediately after

the power supply is turned OFF. If you attempt to replace the fan unit then, there is a risk of personal
injury due to hot or rotating parts.

• Press the power button for several seconds to force the product shutdown. Always back up files in

the planned way to prevent data loss or system file corruption.

• Do not touch any product housing when power is being supplied or immediately after the power sup-

ply is turned OFF. Doing so may result in burn injury.

General Communications

• Separate the machine network segment from the office network to avoid communication failures.

Battery Replacement

Applicable for products with a cooling layer that has a removable cover.

• Dispose of any Battery that has been dropped on the floor or otherwise subjected to excessive

shock. Batteries that have been subjected to shock may leak if they are used.

• UL standards require that only an experienced engineer replace the Battery. Make sure that an ex-

perienced engineer is in charge of Battery replacement.

• The Battery may leak, rupture, heat, or ignite. Never short-circuit, charge, disassemble, heat, or in-

cinerate the Battery or subject it to strong shock.

Cleaning, Maintenance and Disposal

• Do not use corrosive substances to clean the product. Doing so may result in the failure or malfunc-

tion.

• Dispose of the product and batteries according to local ordinances as they apply.

• The following information must be displayed for all products that contain primary lithium batteries

with a perchlorate content of 6 ppb or higher when shipped to or transported through the State of
California, USA.

Perchlorate Material - special handling may apply.
See http://www.dtsc.ca.gov/hazardouswaste/perchlorate.

• The product contains a lithium battery with a perchlorate content of 6ppb or higher. When exporting

an end product containing the product to or shipping through California, USA, label all packing and
shipping containers appropriately.

Precautions for Safe Use

20

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands