manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 87

CFast Card Specifications

Specifications for the CFast Drive are provided in the table below.

Item

Model Specifications

64 GB 

*1

128 GB 

*1

256 GB 

*1

Model 

*2

NY000-AT00

NY000-AT01

NY000-AT02

Type

iMLC

Max. power consumption

0.9 W

Max. sequential
read speed

530 MB/s

Max. sequential
write speed

100 MB/s

190 MB/s

210 MB/s

Operating temperature

-40 to 85°C 

*3

Max. operating humidity
(with no condensation)

10 to 95% RH

Storage temperature

-55 to 95°C

Max. storage humidity
(with no condensation)

10 to 95% RH

Endurance

125 TBW

208 TBW

417 TBW

*1.

Refer to 

1-4 Product Configuration Box PC

 on page 1-5 for product configuration details.

*2.

Refer to 

3-10-4 CFast Cards

 on page 3-24 for brand details.

*3.

Refer to 

4-4-1 Operation Environment Specifications

 on page 4-31 for the temperature specifications of the

complete Box PC.

4 Specifications

4-13

NY-series Industrial Box PC Hardware User's Manual (W553)

4-1 General Specifications

4

4-1-7

 Storage Device Specifications

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands