manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 150

5-4-4

Wire the I/O Connector

This section describes how to wire the I/O connector.

I/O Connector Wiring Materials

Use the supplied I/O connector to connect the inputs and outputs to the Industrial Box PC.
Recommended I/O conductor sizes for the connector are provided in the table.

Wire type

Conductor cross-section

Solid conductor

0.2 to 1.5 mm

2

Flexible conductor
Flexible conductor, with ferrule and no plastic sleeve

0.25 to 1.5 mm

2

Flexible conductor, with ferrule and plastic sleeve

0.25 to 0.75 mm

2

Minimum AWG according to UL/cUL

24

Maximum AWG according to UL/cUL

16

I/O Connections

This section describes I/O connection details.

1

3

5

2

4

6

Pin

Description

Internal Circuit Details

1

Power Status Output

The Power Status Output has an internal relay. Wire this
according to the input device connected to the Power Sta-
tus Output.

2

5 Installation

5-36

NY-series Industrial Box PC Hardware User's Manual (W553)

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands