manualshive.com logo in svg

Omron SYSMAC NY Series, Hardware User Manual

Share
Download
Omron SYSMAC NY Series Hardware User Manual Download Page 95

I/O Connector Power Status Output Details

This section provides details of the Power Status Output relay.
The Power Status Output is a relay between pin 1 and 2 of the I/O Connector.

Power ON Power Status Output Operation

This section provides power ON details of the Power Status Output operation.
The Power Status Output turns ON to indicate that the system has been shut down and the power
supply to the Box PC can be turned OFF.
If power is not turned OFF, the Power Status output will turn OFF when the Box PC is turned ON.

The Power Status Output is ON 

A

 when the Box PC has been used and has not been disconnect-

ed from the power supply.

The Power Status Output is OFF 

B

 when the Box PC has been disconnected from the power sup-

ply.

Power up
start

Power supply has
been disconnected

Open (OFF)

Closed (ON)
Relay

Open (OFF)

Closed (ON)
Relay

A

B

Product ON

Product OFF

Additional Information

Refer to 

5-4-4 Wire the I/O Connector

 on page 5-36 for I/O connector wiring details.

Power OFF Power Status Output Operation

This section provides power OFF details of the Power Status Output operation.
The Power Status Output turns ON to indicate that the system has been shut down and the power
supply to the Box PC can be turned OFF.

If power is not turned OFF, the Power Status output will stay ON 

A

. It will turn OFF when the Box

PC is turned ON.

If power is turned OFF, the Power Status Output will turn OFF 

B

.

4 Specifications

4-21

NY-series Industrial Box PC Hardware User's Manual (W553)

4-2 Connector Specifications

4

4-2-2

 I/O Connector Specifications

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands