Home
/
Omron
/
SYSMAC NY Series
/
Hardware User Manual

Omron SYSMAC NY Series, Hardware User Manual

Share

Page: 172 / 260

Omron SYSMAC NY Series Hardware User Manual Download Page 172

6-2-3

Power OFF Using the Power ON/OFF Input

1

Ensure all programs are closed.
If required, close all active programs.

2

Supply a 24 VDC signal to the Power ON/OFF Input (pins 3 and 4) of the I/O connector.
The input signal must remain ON for a minimum of 60 ms and a maximum of 750 ms to be
correctly detected by the Industrial Box PC.
The Industrial Box PC will shutdown.
Note that this behaviour can be reconfigured with the Power Options settings.

3

Wait until the PWR LED is OFF.

The Box PC is powered OFF.

Additional Information

• Refer to

4-2-2 I/O Connector Specifications

on page 4-19 for connector specifications.

• Refer to

5-4-4 Wire the I/O Connector

on page 5-36 for wiring details.

6-2-4

Forced Power OFF Using the Power Button

Precautions for Safe Use

Press the power button for several seconds to force the product shutdown. Always back up files
in the planned way to prevent data loss or system file corruption.

1

Ensure all programs are closed.
If required, close all active programs to prevent losing unsaved data.

2

Press and hold the power button on the Box PC for 5 to 10 seconds.
Refer to

3-3 Power Button

on page 3-9 for power button location information.

The Industrial Box PC will power OFF.
Any optional operating system settings related to power OFF will be disregarded.

3

Wait until the PWR LED is OFF.

The Box PC is powered OFF.
Confirm normal operation and check all product settings because unsaved data was lost.

6 Operating Procedures

6-4

NY-series Industrial Box PC Hardware User's Manual (W553)

«
...
170
171
172
173
174
...
»

Summary of Contents for SYSMAC NY Series





































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands