Nace CP 1 Course Manual Download Page 420 | Manualshive

Page: 420 / 535

background image

RP0193-2001

NACE International

13

Figure 8: Typical Double-Bottom Cathodic Protection Layout (Impressed or Sacrificial)

8.4 Cathodic Protection Anodes

8.4.1 Either impressed current or galvanic anode
cathodic protection may be used.

8.4.1.1 Galvanic anodes may be magnesium or
zinc. Figure 9 illustrates a typical double-bottom
galvanic anode design.

8.4.1.2 Anode materials that may be used for
impressed current systems include mixed-metal
oxides, polymer carbon, graphite, high-silicon
chromium-bearing cast iron, platinized niobium
(columbium), platinized titanium, scrap metal,
and below-grade metallic structures that have
been removed from service. Figure 10 illustrates
a typical new tank or double-bottom impressed
current anode design.

8.4.1.3 Due

to

the

depolarizing

effect

of

oxidation by-products (typically chlorine, oxygen,

or carbon dioxide) migrating from the anode to
the

steel

cathode,

the

current

density

for

protection with an impressed current system may
be higher than that required for a galvanic anode
system.

8.4.2 Adequate space must be provided between the
two tank bottoms to allow for installation of a cathodic
protection system with uniform current distribution from
the anodes. Due to limited space between bottoms,
close anode spacing may be required to improve
current distribution.

Impressed current anodes must not contact the carbon
steel surfaces of the tank.

8.4.4 Anodes must be installed in a conductive
electrolyte.

The electrolyte must be sufficiently

compacted as to prevent settlement of the replacement
tank bottom.

«
...
418
419
420
421
422
...
»

Summary of Contents for CP 1
























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP 1

Brand: Backyard Discovery Pages: 79

Brand: Badger Meter Pages: 16

Brand: Cadman Pages: 84

Brand: Cambridge Audio Pages: 2

Brand: Quanser Pages: 12

Brand: Danfoss Pages: 106

Brand: Qlight Pages: 4

Brand: Tactile Medical Pages: 23

Brand: Taarup Pages: 72

Brand: B medical systems Pages: 28

Brand: Petzl Pages: 15

Evo TM/TSV2 Awning Wall Set

Brand: Zempire Pages: 2

Brand: GERATHERM Pages: 40

Brand: Stanton Pages: 13

MobilGate - 128c

Brand: SeaSoft Pages: 11

Brand: Cooper Lighting Pages: 1

Brand: Energetics Pages: 89

Brand: Transpak Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands