Nace CP 1 Course Manual Download Page 106 | Manualshive

Page: 106 / 535

background image

Underground Corrosion Control

3:8

CP 1 – Cathodic Protection Tester Course Manual

©

NACE International, 2000

02/01/05

Structures That Can be Cathodically
Protected

Most metallic structures that are immersed or embedded in an electrolyte
can be cathodically protected. Examples of structures where cathodic
protection is employed include:

•

underground or submerged steel, iron, aluminum, and prestressed
concrete cylinder pipelines

•

underground tanks and piping

•

exterior bottoms (both primary and secondary) of above grade
storage tanks.

•

water tank interiors

•

ship hulls

•

ballast tanks

•

docks

•

sheet piling

•

foundation piles on land and in the water

•

bridge decks and substructures

•

hot water storage tank interiors

•

heat exchanger water boxes and tube sheets

•

internal surfaces of oil heater treaters

•

reinforcing steel in concrete

•

lead or steel sheathed telephone and electrical cables.

Cautionary Note:

It is possible to overprotect some materials such as

prestressing wire, lead, and aluminum. High cathodic protection currents
may cause hydrogen embrittlement in highly stressed steel and may
actually increase corrosion of amphoteric metals such as aluminum and
lead.

There are two methods of providing cathodic protection current to a
structure:

•

galvanic anode system

•

impressed current system.

«
...
104
105
106
107
108
...
»

Summary of Contents for CP 1
























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP 1

Brand: Landoll Pages: 6

Brand: ParaBody Pages: 9

Brand: ParaBody Pages: 3

Brand: MacDon Pages: 45

Brand: H&S Pages: 30

Brand: h/p/cosmos Pages: 81

Brand: Rapala Pages: 14

Brand: S.R.Smith Pages: 43

Brand: WalkMed Pages: 2

Brand: Walinga Pages: 20

Brand: Wasp Pages: 50

Brand: Goobay Pages: 6

Brand: Meritor Pages: 65

SeQual Eclipse 5

Brand: CAIRE Pages: 2

Brand: MakAlon Pages: 36

Brand: SureShot Pages: 24

Brand: Sagitter Pages: 12

Brand: Invacare Pages: 271

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands