Nace CP 1 Course Manual Download Page 122 | Manualshive

Page: 122 / 535

background image

Underground Corrosion Control

3:24

CP 1 – Cathodic Protection Tester Course Manual

©

NACE International, 2000

02/01/05

requirement increases. Here again, constant current rectifiers may be
needed.

The same effect occurs in rapidly flowing water. Bridge piles in a rapidly
flowing river will require more current than those in quiescent waters.
Water flow through a heat exchanger water box will also affect the current
requirement.

Make up of the Electrolyte

The electrolyte itself can affect the performance of cathodic protection.
Bacteria, especially sulfate reducing bacteria, have a depolarizing effect on
the protected structures. It may be necessary to increase the level of
cathodic protection in such electrolytes.

The fluid chemistry in oil heater-treaters affects anode performance.
Carbon dioxide and hydrogen sulfide, for example, have a passivating
effect on zinc.

Electrical Shielding

Metal

Metal components connected to a protected structure may prevent cathodic
protection current from reaching a corroding surface. A shorted pipeline
casing is an excellent example of metal shielding.

Figure 3.8 illustrates the effect of a shorted casing.

VENT PIPE

CASING

PIPE LYING ON CASING DUE TO
LACK OF INSULATING SPACERS

END SEAL

Figure 3.8 Cathodic Shielding Due to a Shorted Casing

«
...
120
121
122
123
124
...
»

Summary of Contents for CP 1
























































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CP 1

Brand: Keithley Pages: 36

Brand: Rain-Flo Irrigation Pages: 16

Brand: Rain-Flo Irrigation Pages: 20

Attest Auto-reader 390

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Brand: 3M Pages: 2

PELTOR WS LiteCom Plus

Brand: 3M Pages: 7

Steri-Vac GS Series

Brand: 3M Pages: 52

Brand: Vapotherm Pages: 32

Brand: Vanguard Instruments Pages: 47

Brand: rbd instruments Pages: 18

Brand: GE Pages: 289

Brand: Magicfx Pages: 25

Brand: Valmont Structures Pages: 8

Brand: Gilson Pages: 8

Brand: Turner Designs Pages: 55

ADB KLEMANTIS AS 1000

Brand: Osram Pages: 24

Brand: Harken Industrial Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands