MUTOH ValueJet VJ-1204 Operation Manual Download Page 64

Page: 64 / 186

4 Handling the printer

VJ-1204 OPERATION MANUAL

4-2

4.1

Print flow chart

The following flow chart illustrates the procedure for drawing with the printer.
Refer to each section as required.

WARNING

• Do not store combustible materials on the platen while performing the heater

operation. It could lead to fire.

• Do not spill flammable liquid over the platen. This could lead to fire.

CAUTION

• Do not touch the media guide during printing. It is hot and may cause a burn.

• Do not touch the media feed slot, platen or media guide while heaters are operating.

They are hot and may cause a burn.

• Keep the work area well-ventilated. This prevents fire, and stops operators from

feeling sick from bad air.

NOTE

• Do not open the front cover during printing. If the front cover is opened, printing will be interrupted.

Printing restarts if you close the front cover. However, you are not guaranteed to have high print
quality.

1. Create print data.
Create print data with application software.

↓

2. Turn the power ON and set the media.

3.4 Setting media

4.2 Media

↓

3. Set up printing conditions.

4.3 Menu setups on the operation panel

↓

4. Perform the printing.

4.4 Operating from the operation panel

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands