MUTOH ValueJet VJ-1204 Operation Manual Download Page 101

Page: 101 / 186

VJ-1204 OPERATION MANUAL

5 Panel setup menu

5-17

5.1.7

Winding unit menu

Set the operation of the optional winding unit.

TIP

• For details about the optional winding unit, contact your local MUTOH dealer.

Setup item

Setting

Description

Take-up

<Off>

No use of winding unit.

Type 1

Set to "Type 1" to use the optional winding unit.

NOTE

• When the winding unit is not installed,

please do not set to "Type1".
By doing so, the product will be unable
to function properly.

• When the Winding unit menu is set to

"Type1", the setting for the Prev. Stick
menu is disabled.

5.1.9 Prev. Stick menu

—

• [Enter] key: saves the setting and shifts to the

previous menu.

• [Cancel] key: cancels the setting and shifts to the

previous menu.

5.1 Setup menu

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands