MUTOH ValueJet VJ-1204 Operation Manual Download Page 85

Page: 85 / 186

VJ-1204 OPERATION MANUAL

5 Panel setup menu

5-1

Panel setup menu

The section explains the Setup menu of the printer.

TIP

• The < > parts in each list are factory default settings (initial values).

• For details of the Setup menu, refer to the following manual.

QUICK REFERENCE "Setup menu diagram"

Setup item

Description

Setup menu

Various settings of the printer are configured.

5.1 Setup menu

Test Print menu

Performs nozzle check of the print head and setup list.

5.2 TestPrint Menu

Adjust Print menu

Sets up when adjusting the printer for the optimum quality of image print.

5.3 Adjust Print menu

Cleaning menu

Perform Head cleaning.

5.4 Cleaning menu

Menu Option menu

Sets up the contents of the Setup menu.

5.5 Menu Option menu

Version menu

Displays the versions of the firmware.

5.6 Version menu

Sleep mode menu

Sleep mode settings are configured.

5.7 Sleep Mode menu

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands