MUTOH ValueJet VJ-1204 Operation Manual Download Page 78

Page: 78 / 186

4 Handling the printer

VJ-1204 OPERATION MANUAL

4-16

•

The previous setup menu is displayed.

•

When the main menu is displayed, the screen turns to Normal.

4.3.2

Panel setup menu overview

This sub-section explains the Panel setup menu of the printer.
There are the following items in the Panel setup menu.

TIP

• For details of each setup item, refer to "5 Panel setup menu".

Setup item

Description

Setup menu

Various settings of the printer are configured.

Test Print menu

Performs nozzle check of the print head and setup list.

Adjust Print menu

Print and adjust test patterns for Alignment.

Cleaning menu

Perform Head cleaning.

Menu Option menu

Sets up the contents of the Setup menu.

Version menu

Displays the versions of the firmware.

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands