MUTOH ValueJet VJ-1204 Operation Manual Download Page 139

Page: 139 / 186

VJ-1204 OPERATION MANUAL

6 Maintenance

6-17

6.2

Cleaning the printer

Periodic (every month) cleaning is necessary to use the printer in good condition.

WARNING

• Do not insert or drop metal or flammable objects into the printer through openings

such as a fresh air inlet. It could lead to an electric shock or fire.

• If foreign substances or liquids such as water entered the printer, do not use the

printer as it is. It could lead to an electric shock or fire. Immediately turn OFF the
power switch, disconnect the power plug from the electric socket, and contact your
local MUTOH dealer.

CAUTION

• When cleaning the printer, be sure to turn OFF the power and disconnect the power

plug.

• Do not use volatile solvents such as thinner, benzene, or alcohol. These solvents

could cause damage to the paint.

• Be careful that no moisture enters the printer. There is a possibility that the electric

circuit inside the printer is short circuited.

• Do not open covers attached using screws under any circumstances. This may

cause an electric shock or a malfunction.

This section describes how to clean each part of the printer.

6.2.1

Cleaning the outer case

This sub-section describes how to clean the outer case.
Wipe out dust and dirt attached to the outer case by using a soft cloth.

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands