MUTOH ValueJet VJ-1204 Operation Manual Download Page 155

Page: 155 / 186

VJ-1204 OPERATION MANUAL

7 Troubleshooting

7-3

(2) Does not work after loading the media

(3) When data is sent from the computer, an error occurs at the printer and
nothing is printed

(4) Cannot use the computer online using LAN

No.

Possible cause

Remedy

Reference

Is the front cover open or media
loading lever raised?

Close the front cover.
Lower the media loading lever.

3.4 Setting

media

Is the media loaded at an angle?

Load the media straight.

3.4 Setting

media

Is the ink cartridge inserted?

Insert the ink cartridge.

3.3 Installing ink

cartridges

Are you using the recommended
media?

Use the recommended media.

4.2.1 Media type

Is the printer being used in an
environment other than the one
specified, such as in direct sunlight?

Only use the printer in an environment that
is specified for use.

Installation

manual

No.

Possible cause

Remedy

Reference

Is the type of printer selected correctly
at the computer?

Check that the printer type settings on the
computer side and printer side are the same.

3.7 Connecting

the printer to a PC

Are the interface requirements and
command mode the same on the
computer side and printer side?

No.

Possible cause

Remedy

Reference

Is the network interface cable
connected correctly?

Confirm the types of the cross and straight
cables, and connect the network interface
cable correctly.

3.7.3 Connecting

a network interface
cable

Are the network settings configured
correctly?

Configure the network settings correctly.

5.1.21 IP

Address menu to
5.1.23 Gateway menu

Match the printer’s network settings
with the computer side environment.

Match this product’s network settings with
the computer side environment.

3.7.1 System

requirements

Does the Data lamp on the operation
panel turn on after sending printing
data from the computer?

If the Data lamp does not turn on, contact
the computer manufacturer.

—

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands