MUTOH ValueJet VJ-1204 Operation Manual Download Page 71

Page: 71 / 186

VJ-1204 OPERATION MANUAL

4 Handling the printer

4-9

4.2.6

Media feed compensation

This section explains the Media feed compensation.

The feeding length depends on the media type. The following or similar results may be seen in prints.

•

Printed images overlap.

•

White lines are printed on images.

The accuracy of media feeding may be improved with the following methods.

1. Display the Media feed compensation menu on the operation panel.

a. Press the [Menu] key on the operation panel.

•

"Menu 1: Setup>" is displayed on the operation panel.

•

The operation panel shifts to the Setup menu display.

b. Press the [>] key on the operation panel.

•

"Set1: MediaType" is displayed on the operation panel.

c. Press the [Enter] key on the operation panel.

•

"Media: Type 1" is displayed on the operation panel.

d. Press the [+] key or [–] key on the operation panel to select the media type to use.

e. Press the [Enter] key on the operation panel.

•

"**>1: Print Mode" is displayed on the operation panel.

TIP

• The selected media (Type 1 to 30) is displayed in "**".

5.1.1 MediaType menu

f. Press the [+] key or [–] key to select "**2: PF Adjust".

g. Press the [>] key on the operation panel.

•

"PF1: Initial Print" is displayed on the operation panel.

•

Proceed to Media feed compensation menu.

5.1.1.1.2 Dist.Adj menu

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands