MUTOH ValueJet VJ-1204 Operation Manual Download Page 110

Page: 110 / 186

5 Panel setup menu

VJ-1204 OPERATION MANUAL

5-26

5.1.19 Initialization menu

Returns the settings of the printer to default.

5.1.20 Life Times menu

Displays the operational life time of each part.

NOTE

• When replacing a part that its operational life has ended,

• No charge for replacing within the warranty period or under the contract.

• You are liable for the cost of repairs under conditions other than mentioned above.

• Do not keep using the part which has reached its life span. Problems caused by doing so will not be

covered by the warranty.

Setup item

Setting

Description

Initialization

ALL

All settings can be returned to factory default.

MediaType

The settings of the MediaType menu is returned to
factory default.

Except MediaType

The settings value other than the MediaType menu is
returned to factory default.

—

• [Enter] key:

"Initialing" is displayed on the operation panel and
the printer initializes the setting.

• [Cancel] key: shifts to the previous menu without

initialization.

5.1 Setup menu

Setup item

Setting

Description

Life Times

Head

Display the operational life of each part.
• The operational life of a part is indicated by five

asterisks (100 %).

• As the part deteriorates, the number of asterisks

decreases one by one (20 %).

• The part should be changed when all of the asterisks

have disappeared, and "Change" is displayed.
Contact your local MUTOH dealer to ask for
replacing parts.

Pump

CR Motor

PF Motor

—

• [Cancel] key: shifts to the previous menu.

5.1 Setup menu

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands