MUTOH ValueJet VJ-1204 Operation Manual Download Page 22 | Manualshive

Page: 22 / 186

background image

2 Product overview

VJ-1204 OPERATION MANUAL

2-4

2.2.3

Operation panel

Used for setting operation conditions, display of printer status and various functions.
Names of each operation key and status display along with the functions are explained.

TIP

• Refer to the following for details regarding the operation method of the operation panel.

• When performing menu setting from the operation panel:

4.3 Menu setups on the operation panel

• When performing various operations in the operation panel:

4.4 Operating from the operation panel

(1) Operation keys

NOTE

• The operation keys are assigned with different functions and names depending on printer status

(Normal or Setup menu display). For details about printer status, refer to "2.3 Printer status".

No.

Name

Normal

Setup menu display

1

[Menu] key

Shifts to the Setup menu.

Shifts from Setup menu display to
Normal.

8, 9

3

15

17

16
6

5

11
12

1

13
14

10

2

7

4

«
...
20
21
22
23
24
...
»

Summary of Contents for ValueJet VJ-1204



























































































































































































Reviews:

No comments

Related manuals for ValueJet VJ-1204

Brand: Lanier Pages: 3

imageRUNNER 5075

Brand: Canon Pages: 250

Brand: imagistics Pages: 57

Brand: Compuprint Pages: 38

VersaLink C405/N

Brand: Xerox Pages: 256

Brand: Cycjet Pages: 26

Brand: Partner Pages: 34

Brand: Muratec Pages: 6

Brand: idp Pages: 63

Brand: Pantum Pages: 164

Brand: Mita Pages: 134

Brand: MIMAKI Pages: 30

Brand: Ricoh Pages: 8

Brand: Oce Pages: 227

POCKET PRINTER A6

Brand: SiPix Pages: 24

Brand: SINTERIT Pages: 12

Frontier-S Series

Brand: FujiFilm Pages: 13

Brand: Epson Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands