MUTOH ValueJet VJ-1204 Operation Manual Download Page 45

Page: 45 / 186

VJ-1204 OPERATION MANUAL

3 Before using

3-19

3. Press the [Enter] key on the operation panel.

•

The media type is set.

•

"Media Initial" is displayed on the operation panel and media initial operation starts.

NOTE

• If the following operations are performed in the media type setup menu, the printer starts media

initial operation without specifying a media type.

• Pressing the [Cancel] key on the operation panel.

• No keys on the operation panel are pressed for 10 seconds.

4. After media initial operation is complete, "Ready to Print" is displayed on the operation panel and

the display shifts to Normal.

5. When using the roll media, wind back the roll media tightening with the scroller and the media

slackness is tightened.

•

This completes media loading.

No.

Name

Roll media

Scroller

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands