MUTOH ValueJet VJ-1204 Operation Manual Download Page 28

Page: 28 / 186

3 Before using

VJ-1204 OPERATION MANUAL

3-2

3.1

Power cable connection

This section explains power cable connection.

WARNING

• Be sure to use the power cable supplied with the printer. Using other power cables

can cause an electric shock or fire.

• Do not use a damaged power cable. It could lead to an electric shock and fire.

CAUTION

• Pay attention to the following points when handling power cable.

• Do not do anything forcefully on the power cable.

• Do not put heavy objects on the power cable.

• Do not bend, twist or pull the power cable by force.

• Do not route the power cable near heating appliances.

NOTE

• Contact your local MUTOH dealer in case of power cable damage.

Follow the procedure below to install the power cable.

1. Make sure that the printer is turned OFF.

NOTE

• The power is ON when the [Power] key of the operation panel is pressed in.

Press the key once again to turn OFF the power.

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands