MUTOH ValueJet VJ-1204 Operation Manual Download Page 32

Page: 32 / 186

3 Before using

VJ-1204 OPERATION MANUAL

3-6

3.2.2

Turning the power OFF

Follow the procedure below to turn the printer OFF.

1. Verify the following regarding the operational condition of the product.

•

Printing or other operations are not in progress.

•

The operation panel display is Normal.

•

The Low lamp on the operation panel lights up in green.

NOTE

• If the High lamp on the operation panel lights up in green, the head height is set to High.

Return the head height to Low before turning the power OFF.

4.2.5.2 When returning the print head to the original position

2. Press the [Power] key on the operation panel to turn OFF the printer.

NOTE

• If the operation panel is in the following status, the power is ON.

• The [Power] key is pressed in.

• The Power lamp lights up in green.

Press the key once again to turn OFF the power.

•

The printer starts the procedure to turn the power OFF.

•

"Power Off" is displayed on the operation panel.

Summary of Contents for ValueJet VJ-1204



























































































































































































Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands

MUTOH ValueJet VJ-1204, Operation Manual

Search results

Summary of Contents for ValueJet VJ-1204

Reviews:

Related manuals for ValueJet VJ-1204

Brands by name

Popular brands